Features Control individual outlets or outlet banks Monitor your devices and power status Receive E-mail alerts for power events Schedule tasks such as power on, off, and reboot Manage multiple devices across multiple locations Utilize device-specific features for your compatible product Description Your Gateway to BlueBOLT The BlueBOLT-CV1 Interface Card plugs in to select Panamax/Furman products and provides access to BlueBOLT™ cloud based remote power management technology. Each BlueBOLT-CV1 card includes a unique MAC address and identification number allowing you to create a BlueBOLT account or add a compatible unit to an existing account. The BlueBOLT-CV1 is completely plug-and-play – no static IP addresses to set up or ports to configure. Simply plug the card into a compatible device, connect it to the Internet, register the unit, and you’re ready to go! Look for the BlueBOLT logo The BlueBOLT-CV1 works with any BlueBOLT-Compatible Panamax or Furman product.

A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10Lx E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load. The M-10Lx E features two slide out, swiveling light fixtures to provide discreet illumination of your equipment on stages, in studios, and in other dark places. A dimmer knob lets you adjust the lamp brightness to just the right level.Specifications Maximum Output Current:    10 amps Line Cord:    1.5 meter, removable, IEC C-13 female to Schuko male Lamps:    LED Operating Voltage:    230VAC 50Hz Spike Protection Mode:    Line to neutral Energy Dissipation:    305 joules Peak Impulse Current:    12,000 amps Maximum Continuous Opterating Voltage:    650 Volts Noise Attenuation:    Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz Dimensions:    1.75” H x 19” W x 7.5” D Weight:    2.3 kg. Safety Agency Listing:    CE Warranty:    Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.

A Merit Series Power Conditioner is the perfect low-cost AC power solution for any rack mount system. Install an M-10x E in to the top slot of your rack, and the ten switched outlets in the rear panel will power up and protect all your equipment up to a 10-amp load.   Specifications   Maximum Output Current: 10 amps Line Cord: 1.5 meter, removable, IEC C-13 female to Schuko male Operating Voltage: 230VAC 50Hz Spike Protection Mode: Line to neutral Energy Dissipation: 305 joules Peak Impulse Current: 12,000 amps Maximum Continuous Opterating Voltage: 650 Volts Noise Attenuation: Transverse mode: Greater than 20dB, 1.5Mhz to 200 Mhz Dimensions: 1.75” H x 19” W x 7.5” D Weight: 2.3 kg. Safety Agency Listing: CE Warranty: Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.

The 30 Amp P-6900 AR E delivers clean, stable power to protect equipment from problems caused by AC line voltage irregularities such as sags, brownouts, or overvoltages all of which can cause sensitive electronic equipment to malfunction or sustain damage. The P-6900 AR E accepts any input voltage from 188V to 270V and transforms it to a constant output of 230V or 240V (switchable), ±10V. Voltages beyond that range may also be converted to usable levels, depending on the range variance.Additionally, the P-6900 AR E is a full-featured power conditioner that filters and purifies AC power, reducing line noise and ensuring optimum performance. Not only will your equipment perform better with Furman's Linear Filtering Technology (LiFT), but it will also be fully protected by our exclusive Series Multi-Stage Protection (SMP), and Extreme Voltage Shutdown (EVS). This circuitry provides the highest level of power protection available.Specifications Maximum Current:    30 amps Line Cord:    30A C-Form connector with female mating connector for termination of custom line cord Operating Voltage:    174 to 264 VAC Over-Voltage Shutdown:    275 VAC Nominal Approximate Input Voltage Capture Range:    174 to 264 VAC Spike Protection Mode:    Line to neutral, zero ground leakage Spike Clamping Voltage:    375 VAC peak @ 3,000 Amps Response Time:    1 nanosecond Maximum Surge Current:    6,500 Amps Noise Attenuation:    10 dB @ 10 kHz, 40 dB @ 100 kHz, 50 dB @ 500 kHz Dimensions:    482.6mm W x 597mm D x 133.35mm H Weight:    26 kg. Power Consumption:    5 watts